Month: January 2024

Do you ever ask yourself, “How long does a garage door replacement take in Westchester, NY?” If so, you are not alone. This is one of the most common questions people ask their neighbors, friends, or family members.

Determining how long a garage door replacement takes in Dutchess County is challenging due to various influencing factors, such as the garage door’s make and model and the specific installation procedure used. However, we’ve created a guide to assist you in estimating the time required for removing and installing your garage door.

From there, you can plan accordingly and avoid delays or headaches during your garage door installation in Dutchess County.

How to Remove a Garage Door

If you aim to remove your garage door, follow several steps.

Start by determining the door size, typically 72 inches wide to 79 inches high. Once you have the dimensions, seek an online resource offering instructions on measuring and ordering the correct parts.

Next, procure the necessary tools for door removal. Common tools include a wrench set and a saw. Ensure you have a replacement wrench set in case any original tools break during removal.

Once you’ve purchased all essential tools, begin the door removal process. Firstly, don safety goggles and gloves for protection. Then, using your wrenches, raise the arms of the spring-loaded gate into a horizontal position.

Here’s where the process can become challenging – use one wrench to lift one end of the gate while applying downward pressure on the other end with your feet until it releases from its hinges. Repeat this step until both ends of the gate are detached.

How to Install a Garage Door

If you have just bought a new home and are unpacking, one of the first things you must do is install your garage door. Installing a garage door is a relatively simple task that a handy homeowner can complete in just a few hours. Here are the steps to installing a garage door:

1. Remove any old garage door hardware and screws using an Allen wrench or screwdriver. Leave the brackets on the wall if they are still attached; you will reuse them later.
2. Measure and mark the location of the new brackets on the wall using a level. Use the same measurements as your old brackets (or slightly larger ones) since your new brackets will likely be slightly different sizes than your old ones.

Use this information to drill holes in both new brackets using a drill bit that is slightly smaller than the screw used for attaching your old hardware. Carefully insert the screws into these drilled holes and tighten them with an Allen wrench or screwdriver.

3. Reattach your old garage door hardware to the new brackets by inserting screws into corresponding holes on top of each bracket and then pressing them down onto their respective screws on the door.

Line up these holes with an Allen wrench or screwdriver before tightening them down. If you have replaced your door’s springs, now would be a good time to reattach them to their anchors, too!

How to Adjust the Height of a Garage Door

Step 1: Locate the garage door opener. The opener is usually located near the top of the garage door. If it’s not, locate the wires that control the garage door.

Step 2: Turn off the power to the garage door opener by unplugging its electrical wires from the wall. You may also have to remove a switch or lever on the wall near the opener to do this.

Step 3: Begin by lifting one end of the garage door to reveal the cable guide and pulley system.

Step 4: Position a long ladder against one side of the garage door to gain access for unhooking or unhitching the cables from the guide pulleys

Step 5: Move the ladder’s opposite end to initiate the garage door’s opening.

How to Change the Position of a Garage Door Spring

If your garage door spring is located in the middle of the door, it’s time to change its position. To do this, remove the screws that hold down the spring and set it aside. Then line up the new spring on one side of the garage door and screw it in place. Afterward, screw down the other side of the spring, and you’re done!

How to Repair or Replace a Garage Door Motor

If you’re experiencing trouble opening or closing your garage door, there’s a good chance that the motor is the culprit. In most cases, it’s easy to replace the motor. Here’s how to do it:

1. Remove the screws that secure the door panel to the frame. You’ll also need to remove any trim or molding around the edge of the door panel.
2. Carefully pull off the panel, revealing the motor and controls. If there are any cables attached, disconnect them now.
3. Find a replacement motor online or in your local hardware store. Some motors are universal and will fit many brands of garage doors; others are specific to a certain type of door or brand of opener.
4. Match up the wires on the new motor with those on your old one and connect them using cable ties or wire connectors. Ensure all connections are tight, especially at the tension spring pulley and each drive belt (or chain) end.
5. Replace screws and bolts that secure the motor to the frame, then reinstall any trim or molding around the edge of your new panel. Test your garage door several times by closing and opening it to ensure everything works correctly.

How Long Does it Take to Remove and Install a Garage Door?

If you’re looking for an easy and fast way to remove and install a garage door, it might not be your best option. Garage door removal and installation can take 30 minutes to several hours. And it depends on the size of your garage, your skill level, and the condition of your door.

To remove a typical garage door, first, identify which hinge needs to be removed to raise or lower the door. Next, a pry bar or screwdriver pops the hinge off its axis. Be careful not to scratch or damage the door’s surface while doing this. You can then pull the door off its track and set it aside.

If walls or fences on all sides enclose your garage, you must install an access panel to complete the removal process. This panel will allow you to remove screws that secure the top edge of the door panel to the frame of your garage wall. Once these screws are removed, lift the panel, and set it aside.

When it comes time to install a new garage door, follow these same steps in reverse order. First, remove any existing screws that secure the bottom edge of your new door panel to the floor of your garage. Then set up your new panel against the wall of your garage and attach it using screws that have been provided with your kit. Finally, replace any screws that were removed when removing the old door.

Leave the Hassle to the Experts, Contact Whitaker Garage Doors Today for an Estimate!

Are you thinking of getting a new garage door, or are you just curious how long it takes to remove and install it? Call Whitaker Garage Doors today at (914) 690-7952 for a FREE estimate! We can provide an accurate time frame for the entire process, from initial consultation to final installation.

We understand that not everyone is familiar with the intricacies of garage doors, so we’ll be happy to walk you through every step of the process. Our knowledgeable staff is always available to answer any questions or help solve any difficulties.